Mini Split Install Sub for Round Rock Builders
You need a mini split sub that gives you a flat number today and shows up on the day you need them. No timeline surprises. No client-facing mess. One number to plug into your bid. One phone call to repeat across jobs.
| Standard single zone install, weekday | $2,400 materials and labor |
|---|---|
| Same install, Saturday or Sunday | $2,600 materials and labor |
| Joker day | One day each week priced under the weekday rate, day shown on the home page |
| Booking deposit | $400 toward materials |
| Balance | Due on completion |
| Non standard work | Quoted before any work begins |
| Bid line item | Standard single zone mini split install, $2,400 weekday (materials and labor) |
| Note | Standard install covers one indoor head and one outdoor unit |
| Note | Site walk confirms line set route, drain path, circuit size, equipment location |
| Note | Point of contact: same phone number for bid, scheduling, and site questions |
| Scope confirmed | At the site walk |
| Contact | (512) 297-7493 |
The Bid Number You Can Plug In Today
Standard single zone mini split install is $2,400 on a weekday. That is materials and labor. No hidden fees. No add-ons at the end.
Weekend work is $2,600. There is one Joker Day each week priced lower than the weekday rate. That day changes week to week. Check the home page for which day it lands on.
A $400 materials deposit books your date. Balance is due on completion. Non standard work is quoted before any work begins.
How Scheduling Works Across Jobs
You pick the date. It gets confirmed. If anything changes, you get told.
The install happens on the day the drywall crew leaves. That keeps your timeline moving. The client sees a clean unit at walkthrough, not a half finished job.
To set up repeat scheduling across multiple projects, call (512) 297-7493. One number for every bid, every date, every job.
What the Site Walk Covers
Before any work starts, we walk the site. This confirms what you already know about the space and eliminates surprises.
Line set length gets confirmed at the site walk. Circuit size, drain routing, penetration location, and equipment size all get confirmed at the site walk.
Sizing is a rule of thumb confirmed on site. A casita reads smaller than it loads. West glass and a hot attic push the size up. The final size gets confirmed on site.
What Stays Out of Your Way
The crew works without tying up your subs. They need the wall open and the electrical rough in done. That is it.
The install is clean. Lines are run tight. The unit is mounted level. No mess left for the client to see at walkthrough.
Non standard work gets quoted before it starts. You know the cost before we proceed. No back charges after the fact.
Service Area and Contact
Service area is Austin and the I-35 corridor. Round Rock is a primary market for this page.
Call (512) 297-7493 for a bid, to schedule, or to set up repeat work. One phone call covers it all.
Included in the number
- Mount one indoor wall unit
- Mount one outdoor condenser on pad or bracket
- Run line set between indoor and outdoor units
- Connect line set and vacuum test the system
- Install a condensate drain line to an accessible drain point
- Provide and install a standard electrical whip to the outdoor unit
- Test operation and verify cooling and heating modes
- Clean up the work area and remove debris
Quoted before work begins
- Custom drain routing beyond a straight gravity run
- Line set longer than the standard allowance confirmed at site walk
- Exterior line set cover or concealment in finished walls
- Structural reinforcement for wall or ceiling mount
- Electrical panel work or new circuit installation
- Hoisting equipment for attic or rooftop access
Have these done before the install date and the day runs clean. Anything not on this list gets looked at during the site walk.
- Wall open and accessible for line set and drain routing
- Electrical rough in complete with disconnect within sight of outdoor unit
- Outdoor unit location clear and level (pad or bracket installed by others)
- Drain path identified and unobstructed to an approved discharge point
- No other trades working in the same zone on install day
- Client or GC point of contact available for site walk coordination
- Site PrepCrew confirms power is off and work area is clear. Sets up drop cloths and staging for tools and materials.
- Line Set and Drain RunLine set and condensate drain are routed from indoor unit location to outdoor unit location. Penetrations are sealed.
- Indoor Unit MountIndoor head is mounted on the wall bracket. Drain line is connected and tested for slope.
- Outdoor Unit and ConnectionsOutdoor condenser is set on pad or bracket. Line set is connected and vacuum pulled to remove moisture and air.
- Startup and WalkthroughSystem is powered on and tested in cooling and heating modes. Crew reviews operation with client or GC and cleans the work area.
Phases run in this order on a standard job. Site conditions change the pace, so nothing here is a timeline commitment. If something on site is different from the walk, you get told before it turns into cost.
$400 materials deposit books the date and buys the equipment for your job. Balance due on completion, on the visit the system runs.
$2,400 weekday. $2,600 Saturday or Sunday. One Joker day each week is priced under the weekday rate. The day moves week to week and it is shown on the home page, so if your schedule has slack you can aim at it.
Non standard work is quoted before any work begins. Nothing gets added to the number without you approving it first.
Running the same install across more than one project? Call (512) 297-7493 to set up repeat scheduling.
- What is included in the $2,400 weekday price?
- Materials and labor for a standard single zone install. One indoor head and one outdoor unit. Line set, drain line, electrical whip, and vacuum test are included. Non standard work like long line sets or custom drain routing is quoted before it starts.
- How do I schedule for multiple jobs?
- Call (512) 297-7493 to set up repeat scheduling. We can book dates across your projects in Round Rock and the Austin area. Each job gets its own confirmed date.
- What happens if the install needs more work than standard?
- Non standard work is identified at the site walk and quoted before any work begins. You approve the quote before we proceed. No surprise charges at the end.
- When do you need the site ready?
- The wall must be open for line set and drain routing. Electrical rough in must be complete with a disconnect near the outdoor unit. The outdoor unit location needs to be clear and level.
- What if the client wants the unit moved after install?
- Relocation is non standard work and would be quoted separately. It is not included in the standard install price.
One number, one call, one line item in Round Rock, Texas. Standard single zone mini split install is $2,400 on a weekday and $2,600 on a weekend, materials and labor, $400 deposit to book, balance due on completion.